A Study on the Mechanical Properties of Green Concrete

Kanmalai Williams, Balamuralikrishnan R., Adams Joe, Shalin Prince

Abstract


Green concrete is a type of concrete that uses waste materials as one of its ingredients. Hazardous wastes like fly ash and silica fume can be used to partially replace cement in concrete, which varies in physical and chemical properties. On the other hand, the increase in automobiles in urban and rural areas has led to an increase in the number of waste tires, which promotes environmental pollution due to disposal issues throughout the world. This study aims to use waste materials which can partially replace cement and conventional aggregates in the concrete mix. Fly Ash (FA), Silica Fume (SF), and Plaster of Paris (PP) replaced cement, whereas Reclaimed Rubber (RR) partially replaced coarse aggregates by weight. This work is focused on experimentation and simulation of M 40 grade mix using the above four materials. 306 cubes were cast by replacing cement with FA, SF, and PP in 3% increments up to 24%. Similarly, coarse aggregates were replaced with RR using the same proportion. Compression tests were carried out using a Universal Testing Machine. 12% silica fume replacement exhibited maximum strength during individual replacement of materials in concrete, which is selected as the optimum percentage replacement. FA and PP developed ultimate strength at 9% replacement of cement in the concrete mix, which is considered the optimum replacement percentage. A Genetic Algorithm (GA) model was developed using a C++ program to simulate various combinations of FA, SF, PP, and RR based on individual optimum replacement percentage. Hence, 1600 combinations were identified with the above four materials. Hence, GA was used as a tool to simulate the compressive strength of concrete to reduce time and cost. During simulation of combined replacement using GA, very high and very low compressive strength values were neglected, and 32 combinations were selected based on optimum compressive strength values. Finally, five combinations (C1-C5) were recognized, which resulted in higher compressive strength than individual optimum values after simulation. The GA-based numerical results were validated by casting 15 cubes for all the five combinations. 15 beam samples of size 100 150 1500 mm were cast with the above five combinations, cured and tested using a loading frame. A load-deflection curve was plotted, which showed that material replacement increased the flexural strength of the concrete mix.

 

Doi: 10.28991/CEJ-2022-08-05-012

Full Text: PDF


Keywords


Strength Prediction; Compressive Strength; Flexural Strength; Reclaimed Rubber; Admixtures; Genetic Algorithm.

References


Guo, Y.-L., Liu, X.-Y., & Hu, Y.-P. (2021). Study on the influence of fly ash and silica fume with different dosage on concrete strength. E3S Web of Conferences, 237, 03038. doi:10.1051/e3sconf/202123703038.

Karthik Prabhu, T., Subramanian, K., Jagadesh, P., & Nagarajan, V. (2019). Durability properties of fly ash and silica fume blended concrete for marine environment. Indian Journal of Geo-Marine Sciences, 48(11), 1803–1812.

Menéndez, E., Argiz, C., & Sanjuán, M. Á. (2021). Coal ash Portland Cement Mortars Sulphate Resistance. Civil Engineering Journal, 7(1), 98–106. doi:10.28991/cej-2021-03091640

Chopra, P., Sharma, R. K., & Kumar, M. (2016). Prediction of Compressive Strength of Concrete Using Artificial Neural Network and Genetic Programming. Advances in Materials Science and Engineering, 2016, 1–10. doi:10.1155/2016/7648467.

Ali, T., Buller, A. S., Abro, F. U. R., Ahmed, Z., Shabbir, S., Lashari, A. R., & Hussain, G. (2022). Investigation on Mechanical and Durability Properties of Concrete Mixed with Silica Fume as Cementitious Material and Coal Bottom Ash as Fine Aggregate Replacement Material. Buildings, 12(1). doi:10.3390/buildings12010044.

Valente, M., & Sibai, A. (2019). Rubber/crete: Mechanical properties of scrap to reuse tire-derived rubber in concrete; A review. Journal of Applied Biomaterials & Functional Materials, 17(1_suppl), 228080001983548. doi:10.1177/2280800019835486.

Ahmad, A., Farooq, F., Niewiadomski, P., Ostrowski, K., Akbar, A., Aslam, F., & Alyousef, R. (2021). Prediction of compressive strength of fly ash based concrete using individual and ensemble algorithm. Materials, 14(4), 1–21. doi:10.3390/ma14040794.

Raj Kishore, G. V. V. (2021). Experimental study on Strength Attainment of concrete containing silica fume and fly ash. IOP Conference Series: Materials Science and Engineering, 1197(1), 012003. doi:10.1088/1757-899x/1197/1/012003.

Bajpai, R., Choudhary, K., Srivastava, A., Sangwan, K. S., & Singh, M. (2020). Environmental impact assessment of fly ash and silica fume based geopolymer concrete. Journal of Cleaner Production, 254, 120147. doi:10.1016/j.jclepro.2020.120147.

Mane, K. M., Kulkarni, D. K., & Prakash, K. B. (2019). Properties and microstructure of concrete using pozzolanic materials and manufactured sand as partial replacement of fine aggregate. SN Applied Sciences, 1(9), 1–10. doi:10.1007/s42452-019-1059-2.

Mohajerani, A., Kurmus, H., Conti, D., Cash, L., Semcesen, A., Abdurahman, M., & Rahman, M. T. (2022). Environmental impacts and leachate analysis of waste rubber incorporated in construction and road materials: A review. Science of the Total Environment, 835, 155269. doi:10.1016/j.scitotenv.2022.155269.

Liu, J., Fan, X., Li, Z., Zhang, W., Jin, H., Xing, F., & Tang, L. (2022). Novel recycling application of high volume municipal solid waste incineration bottom ash (MSWIBA) into sustainable concrete. Science of the Total Environment, 838, 156124. doi:10.1016/j.scitotenv.2022.156124.

Saraswathy, V., Karthick, S., Lee, H. S., Kwon, S. J., & Yang, H. M. (2017). Comparative Study of Strength and Corrosion Resistant Properties of Plain and Blended Cement Concrete Types. Advances in Materials Science and Engineering, 2017. doi:10.1155/2017/9454982.

Pertiwi, D., Theresia, M. C. A., & Komara, I. (2021). The impact of different of coarse aggregate size on the strength and performance of concrete using locally available materials. Nveo-Natural Volatiles & Essential Oils Journal | Nveo, 8(5), 10332-10340.

Devadass, T. (2019). Experimental study on replacement of fine aggregate in concrete with dissimilar curing conditions. Case Studies in Construction Materials, 11, e00245. doi:10.1016/j.cscm.2019.e00245.

Siddique, R., Singh, M., & Jain, M. (2020). Recycling copper slag in steel fibre concrete for sustainable construction. Journal of Cleaner Production, 271, 122559. doi:10.1016/j.jclepro.2020.122559

Nedeljković, M., Visser, J., Šavija, B., Valcke, S., & Schlangen, E. (2021). Use of fine recycled concrete aggregates in concrete: A critical review. Journal of Building Engineering, 38, 102196. doi:10.1016/j.jobe.2021.102196.

Namagga, C., & Atadero, R. A. (2009). Optimization of fly ash in concrete: High lime fly ash as a replacement for cement and filler material. World of Coal Ash Conference (WOCA), 4-7 May 2009, Lexington, KY, USA.

Liu, D., Gao, J., Yang, Y., Ding, Y., Guo, C., … Xu, W. (2022). Influence of addition of two typical activated carbons on fertility properties and mechanical strength of vegetation concrete under freeze-thaw conditions. Science of the Total Environment, 838, 156446. doi:10.1016/j.scitotenv.2022.156446.

Jagan, S., & Neelakantan, T. R. (2021). Effect of silica fume on the hardened and durability properties of concrete. International Review of Applied Sciences and Engineering, 12(1), 44–49. doi:10.1556/1848.2020.00129.

Al Karawi, R. J., Borhan, T. M., Al Karawi, M. Q., & Al-Hassnawi, N. (2019). Study the Effect of Sawdust Content and Temperature on Fundamental Properties of Plaster Mortars. Journal of Southwest Jiaotong University, 54(4), 1–8. doi:10.35741/issn.0258-2724.54.4.32.

Kenawy, S. H., & Khalil, A. M. (2021). Reclaiming waste rubber for a green environment. Biointerface Research in Applied Chemistry, 11(1), 8413–8423. doi:10.33263/BRIAC111.84138423.

Demissew, A. (2022). Comparative Analysis of Selected Concrete Mix Design Methods Based on Cost-Effectiveness. Advances in Civil Engineering, 2022, 1–8. doi:10.1155/2022/4240774.

Khan, F. A., Shahzada, K., Sami Ullah, Q., Fahim, M., Khan, S. W., & Badrashi, Y. I. (2020). Development of Environment-Friendly Concrete through Partial Addition of Waste Glass Powder (WGP) as Cement Replacement. Civil Engineering Journal, 6(12), 2332–2343. doi:10.28991/cej-2020-03091620.

Herki, B. M. A. (2020). Effect of different curing regimes on capillarity of concrete incorporating local materials. Journal of Critical Reviews, 7(4), 524–530. doi:10.31838/jcr.07.04.98.

Talaat, A., Emad, A., Tarek, A., Masbouba, M., Essam, A., & Kohail, M. (2021). Factors affecting the results of concrete compression testing: A review. Ain Shams Engineering Journal, 12(1), 205–221. doi:10.1016/j.asej.2020.07.015.

Zhao, Y., Yu, M., Xiang, Y., Kong, F., & Li, L. (2020). A sustainability comparison between green concretes and traditional concrete using an emergy ternary diagram. Journal of Cleaner Production, 256, 120421. doi:10.1016/j.jclepro.2020.120421.

De Carvalho Gomes, S., Zhou, J. L., Zeng, X., & Long, G. (2022). Water treatment sludge conversion to biochar as cementitious material in cement composite. Journal of Environmental Management, 306, 114463. doi:10.1016/j.jenvman.2022.114463.


Full Text: PDF

DOI: 10.28991/CEJ-2022-08-05-012

Refbacks

  • There are currently no refbacks.




Copyright (c) 2022 kanmalai williams

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.
x
Message